top of page
Standard Partitions
Standard Partitions may be specified with confidence for non-load bearing partitions and use fast drywall construction techniques.
-
For both commercial and domestic partitions
-
Versatile systems to meet nearly every performance requirement.
-
Minimum amount of components
These systems can utilise the entire range of boards, including wallboard, moisture board, sound shield, fire shield,and dense shield, depending on the performance required. The boards are fixed onto a lightweight metal stud. C stud partitions provide the simplest and most economical system, whilst I stud partitions should be used when a more rigid partition is required, without increasing the overall thickness.
Metal Furring Linings
The system can be applied to the majority of all common masonry substrates. Pre-treatment of the background may be needed, depending on the background condition and the fixing method adopted. Any deleterious deposits, such as mould, oil or grease, must be removed.
Metal Furring linings can be used for most masonry backgrounds depending on the condition:
-
Where the background is uneven and not suitable for direct bonding
-
Where foil backed boards are used for the lining
-
Where insulation is not required within the wall lining void
-
Where only shallow service runs are required to be accommodated within the lining void
-
For a stand-off of 20-35 mm
Wall Liner Linings
Wall liner linings may be specified with confidence for application to most masonry backgrounds depending on the condition.
-
Where a variable stand off clearance is required between lining and background of between 17 and 125mm
-
Where the background is out true./li>
-
Where insulation is required within the wall lining void./li>
-
Where deep service runs are required to be accommodated within the lining void./li>
This system can utilise the entire range of boards available depending on the performance requirements. The boards are fixed onto a lightweight metal framework of channels fixed to brackets fixed to the background. This makes it capable to override substantial irregularities in the background. The lining void facilitates the introduction of thermal or acoustic insulation and provides containment for service runs. The system can be applied to the majority of all common building substrates.
Independent I stud wall linings may be used where background is not suitable to receive other types of lining. Where the wall lining is required to be completely independent of an adjacent wall structure
Direct to Timber Ceilings
Direct to timber ceilings is the method for attaching plasterboard to the underside of timber floor joists and roof trusses. This system is widely used to line new ceilings or existing ceilings and can incorporate any type of plasterboard to maintain the performance required.
MF Ceiling System
The MF Ceiling system can accept some degree of loading and is the more traditional form of application. This system can utilise one or more layers of the entire range of plasterboards depending on the performance required. The boards are fixed onto a lightweight metal framework of primary channels, MF ceiling channels and perimeter channels. The lightweight galvanised grid is suspended by either strap hangers or angle sections fixed to the structural soffit with soffit cleats.
Suspended Ceilings
-
Where access to the ceiling void is required.
-
Where an acoustic absorption performance is required.
-
Where hygiene is a key criteria.
-
Where no decorating is possible.
The tiles are placed in a galvanised steel grid system hung from the structural soffit by either wire or angle sections.
Suspended Ceilings can be installed to the majority of all applications to create personalised ceilings and meet technical requirements such as acoustics, moisture, hygiene and fire. This system can utilise many different styles, colours and textures of tiles.
Direct Bonding
-
When minimum cost and simplicity of application is required
-
Where the background is plumb, dry and sound
-
For a stand off of 10-25mm.
This system utilises one layer of plasterboard or insulating laminate boards. These boards are fixed with bonding compound in a regular pattern known as dot & dab, allowing the boards to be fixed with minimum projection. The system allows overriding nominal irregularities in the background and will accommodate shallow service runs within the lining void.
Direct Bonding may be specified with confidence for application to most masonry backgrounds depending on the condition.
Tape and Jointing
The tape and jointing system is used for the seamless jointing of tapered edge boards to walls and ceilings. Jointing of all flat, internal and external corner joints is achieved with the application of two coats of joint filler and one coat of joint cement to leave a smooth finish ready for decoration. This means for faster setting and drying times, obviously permitting quicker decoration. Only a small amount of material is required on site compared to wet plaster.
Dry Walling
We understand the importance of picking the right company that’s experienced, dependable and affordable. With this service and our many others, we have the tools and experience to get the job done with the highest standards and at the best price. We have extensive experience in offering design, planning and delivery of the ideal drywall systems to meet the requirements of your project. Let us know how we can help with your needs.
Suspended Ceilings
EasyFix Ltd has loads of experience with dry walling, using respected equipment brands and trusted material providers. We offer professional and experienced help with your projects, helping to match your unique needs and budget. We strive to provide great customer service and clear communication so you can understand the progress of your job at every phase. We offer a full design and installation of a variety of suspended ceilings ranging from plasterboard, lay-in grid tiles and light troughs to both commercial and residential buildings.
Lightweight Steel Framing Systems
We offer a full design and installation of Steel Framing Systems which is a lightweight solution that can provide a structural support for both internal and external finishes.Turn your construction project into the vision of your dreams by utilising this service. Our experts will explain all your options and answer any of your questions. Our team works closely with each client to make sure we’re meeting, and exceeding expectations. Get in touch for more information.
Shelving from plasterboard and other wall furniture
EasyFix Ltd can provide effective, modern and economic solutions regarding wall shelving and other interesting wall designs which can assist you in a variety of different ways. We understand the importance of picking the right company that’s experienced, dependable and affordable. With this service and our many others, we have the tools and experience to get the job done with the highest standards and at the best price. Let us know how we can help with your needs.
Services: Services
bottom of page